Profibus PA / Foundation Fieldbus Transmitter – PR Electronics 5350A

Features

  • PROFIBUS PA ver. 3.0
  • FOUNDATION Fieldbus ver. ITK 4.6
  • Automatic switch between protocols
  • Basic or LAS capability with F.F.
  • For DIN form B sensor head mounting
Enquiry

Application

  • Linearized temperature measurement with RTD or TC sensor.
  • Difference, average or redundancy temperature measurement with RTD or TC sensor.
  • Linear resistance, potentiometer and bipolar mV measurement.

Technical characteristics

  • Bus transmitter with both PROFIBUS PA and FOUNDATION Fieldbus communication. A unique switch function ensures automatic shift between the two protocols.
  • Set-up for PROFIBUS PA can be done via Siemens Simatic® PDM®, ABB Melody / Harmony and Metso DNA software and for FOUNDATION Fieldbus via Emerson DeltaV, Yokogawa CS 1000 / CS 3000, ABB Melody / Harmony and Honeywell Experion software.
  • The simulation mode function can be activated by way of a magnet.
  • Polarity-independent bus connection.
  • 24 bit A/D converter ensures high resolution.
  • PROFIBUS PA function blocks:
    2 analog.
  • FOUNDATION Fieldbus function blocks:
    2 analog and 1 PID.
  • FOUNDATION Fieldbus capability:
    Basic or LAS.

Mounting / installation

  • For DIN form B sensor head or DIN rail mounting with the PR fitting type 8421.

Specification

ENVIRONMENTAL CONDITIONS
Operating temperature -40°C to +85°C
Calibration temperature 20…28°C
Relative humidity < 95% RH (non-cond.)
Protection degree (encl./terminal) IP68 / IP00
MECHANICAL SPECIFICATIONS
Dimensions Ø 44 x 20.2 mm
Weight approx. 55 g
Screw terminal torque 0.4 Nm
Vibration DIN class B, IEC 60068-2-6 and IEC 60068-2-64
2…25 Hz ±1.6 mm
25…100 Hz ±4 g
COMMON SPECIFICATIONS
Supply
Supply voltage 9.0…32 VDC
Max. required power < 350 mW
Isolation voltage
Test voltage 1.5 kVAC for 60 s
Working voltage 50 VRMS / 75 VDC
Response time
Response time (programmable) 1…60 s
Quiescent current < 11 mA
Max. current increase in the event of an error < 7 mA
Warm-up time 30 s
Signal / noise ratio Min. 60 dB
Updating time < 400 ms
Execution time, analog input < 50 ms
Accuracy Better than 0.05% of selected range
Signal dynamics, input 24 bit
EMC immunity influence < ±0.1% of reading
Extended EMC immunity: NAMUR NE21, A criterion, burst < ±1% of reading
INPUT SPECIFICATIONS
RTD input
RTD type Pt25…1000, Ni25…1000, Cu10…1000, lin. R, potentiometer
Cable resistance per wire 50 Ω (max.)
Sensor current Nom. 0.2 mA
Effect of sensor cable resistance (3-/4-wire) < 0.002 Ω / Ω
Sensor error detection Yes
Short circuit detection < 15 Ω
TC input
Thermocouple type B, E, J, K, L, N, R, S, T, U, W3, W5
Cold junction compensation (CJC) < ±0.5°C
Sensor error detection Yes
Sensor error current: When detecting / else Nom. 4 μA / 0 μA
Short circuit detection < 3 mV
Voltage input
Measurement range -800…+800 mV
Input resistance 10 MΩ
OUTPUT SPECIFICATIONS
PROFIBUS PA connection
PROFIBUS PA protocol Profile A&B, ver. 3.0
PROFIBUS PA protocol standard EN 50170 vol. 2
PROFIBUS PA address (at delivery) 126
PROFIBUS PA function blocks 2 analog
FOUNDATION Fieldbus connection
FOUNDATION Fieldbus protocol FF protocol
FOUNDATION Fieldbus protocol standard FF design specifications
FOUNDATION Fieldbus version ITK 4.6
FOUNDATION Fieldbus capability Basic or LAS
FOUNDATION Fieldbus function blocks 2 analog and 1 PID
OBSERVED AUTHORITY REQUIREMENTS
EMC 2014/30/EU
RoHS 2011/65/EU
EAC TR-CU 020/2011
APPROVALS
ATEX KEMA 02ATEX1318 X
CSA 1418937
FM 3015609
NEPSI GYJ14.1100U
EAC Ex RU C-DK.HA65.B.00355/19

Download

PR Electronic 5350A Profibus PA-Foundation Fieldbus transmitter-DpstarGroup

Reviews

There are no reviews yet.

Be the first to review “Profibus PA / Foundation Fieldbus Transmitter – PR Electronics 5350A”

Your email address will not be published. Required fields are marked *