MR13 Series is controller in 1 with input 3 points, setting 3 points, and output 3 points.
Digital Controller – Shimaden MR13 Series
Features
- 3-channel controller, 3-channel input, 3-channel setting and simultaneous 3-channel display are possible
- Accuracy: ± (0.3% FS + 1 digit)
- Follow-up type PV input function
- Follow-up type SV setting function
- Remote/local and DI input function
- Programmable 1 pattern with 9-step function
- Included a new processing system, Expert PID, remarkably improved PID control efficiency; overshoot and undershoot are controlled effectively.
- Interface RS232C/RS485
Specification
| Display | |
| LED display | PV display 7-segment LED green 4 digits 3 channels to be displayed individually. |
| SV display 7-segment LED orange 4 digits | |
| CH display 7-segment LED orange 1 digit | |
| Action display LED | Control output display: 3-OUT1, OUT2, OUT3 |
| Auto tuning | 1-AT |
| Follow type SV display | 1-FLW Program RUN: 1-RUN |
| Event output display | 3-EV1, EV2, EV3 |
| Remote input display | 1-REM Communication display: 1-COM |
| Display accuracy | ±(0.3%FS + 1 digit) Standard accuracy |
| Temperature range in which accuracy is maintained | 23 °C±5 °C |
| Display resolution | Depends on measuring range (0.001, 0.01, 0.1, 1) |
| Sampling cycle | 0.5 seconds |
| Measured value display range | -10% to 110% of measuring range |
| Setting | |
| Setting | By 6 front key operation |
| Setting range | Same as measuring range |
| Higher/lower limit setting limiter | Higher and lower limits to be set separately; free within measuring range (Lower limit < higher limit) |
| Follow type SV setting | SV of CH2 or CH3 can be set to follow CH1 (deviation setting) (on condition that measuring range of CH2 or CH3 is the same as that of CH1.) |
| Input | |
| Input type has to be the same for 3 channels (measuring range can be selected individually). | |
| Thermocouple | B, R, S, K, E, J, T, N, PL II, WRe5-26, {L, U (DIN43710)} |
| (Multiple input, multiple range. Refer to measuring range code table.) | |
| External resistance | 100Ω maximum |
| Input impedance | 500kΩ minimum |
| Burnout | Standard feature (up scale) |
| Cold junction temperature compensation accuracy | ±2.0 °C (5–45 °C) |
| R.T.D. | JIS Pt100/JPt100 3-wire type (Multiple range. Refer to measuring range code table.) |
| Amperage | Approx. 0.25 mA |
| Lead wire tolerable resistance | 5Ω maximum/wire |
| Voltage | ±10, 0–10, 0–20, 0–50, 10–50, 0–100mV DC, or ±1, |
| 0–1, 0–2, 0–5, 1–5, 0–10V DC | |
| (Multiple input, programmable range. Refer to measuring range code table.) | |
| Input impedance | 500kΩ minimum |
| Current | 4–20, 0–20mA DC |
| (Multiple input, programmable range. Refer to measuring range code table.) | |
| Receiving impedance | 250Ω |
| Sampling cycle | 0.5 seconds |
| PV bias | ±1999 digit |
| PV filter | OFF, 1–100 seconds |
| Follow type PV input | PV input of CH2 or CH3 can be set to follow CH1 (deviation setting) (on condition that measuring range of CH2 or CH3 is the same as that of CH1.) |
| Isolation | Insulated between input and various outputs (not insulated between input and system, remote input and DI input) |
| Control | |
| Control mode | Expert PID control with auto tuning function |
| Proportional band (P) | OFF, 0.1–999.9%FS (OFF=ON/OFF action) |
| Integral time (I) | OFF, 1–6000s (OFF=P, PD action with manual reset) |
| Derivative time (D) | OFF, 1–3600s (OFF=P, PI action) Manual reset: ±50.0% |
| ON/OFF hysteresis | 1–999 digit |
| Proportional cycle | 0.5–120.0 seconds (0.5 sec. is unit for setting.) |
| Control output characteristics | RA/DA selectable (set to RA when shipped) |
| Output limiter | Higher limit, lower limit 0.0–100.0% (lower limit < Higher limit) |
| Soft start | OFF, ON (Fixed to 10 sec.; Valid when power is turned on, RTS RUN, and when returned from scaleover.) |
| Control output/rating | |
| Output specification has to be the same for 3 channels. | |
| Contact output (Y) | 1a 240V AC 2.5A/resistive load |
| Current output ( I ) | 4–20mA, 0–10mA DC/load resistance 600Ω maximum. |
| SSR drive voltage output (P) | 15V±3V DC/ Load current 20mA maximum |
| Voltage output (V) | 0–10V DC/Load current 2mA maximum |
| Operation output updating cycle | 0.5 second |
| Isolation | Insulated between control output and system and input (not insulated between control output I, P or V and analog output) |
| Event output (optional) | |
| Number of outputs | : 3 -EV1, EV2, EV3 (Selectable from CH1, CH2 and CH3, individual setting, individual output) |
| Output rating | : Contact output 1a (common) 240V AC / 1A (resistive load) |
| Setting | : Individual setting |
| 0) NON : Not assigned | |
| 1) DEV : Higher limit deviation value alarm | |
| 2) DEV : Lower limit deviation value alarm | |
| 3) DEV : Higher/lower limit value alarm in case SV is out of measuring range | |
| 4) DEV : Higher/lower limit value alarm in case SV is within measuring range | |
| 5) PV : Higher limit absolute value alarm | |
| 6) PV : Lower limit absolute value alarm | |
| 7) SO : ON upon scaleover | |
| 8) RUN : ON during program RUN | |
| 9) END : ON for 1 sec. upon termination of program | |
| 10) STEP : ON for 1 sec. upon termination of program step | |
| Hysteresis | 1–999 digit (when DEV or PV has been selected) |
| Standby action | Selectable (when DEV or PV has been selected) |
| Action delay time | OFF, 1–9999 seconds (when DEV or PV has been selected) |
| Isolation | Insulated between alarm output and various inputs/outputs and system |
| Remote setting (optional, selectable between this function and DI) | |
| Setting signal | 1–5V, 0–10V, 4–20mA |
| Setting range | Same as measuring range |
| Accuracy of setting | ±(0.3%FS+1) digit |
| Channel for setting | Selectable from CH1, CH2 and CH3 |
| Remote scaling | Within measuring range (inverted scaling possible) |
| Remote bias | -1999–5000 digit |
| Remote filter | OFF, 1–100 seconds |
| Sampling time | 0.5 second |
| Isolation | Insulated between remote input and various outputs (not insulated from system and various inputs) |
| External control input (DI) (optional, selectable between this function and remote setting) | |
| Number of input point | 1 |
| Input rating | Non-voltage contact, open collector input (about 5V/0.4mA DC impress) |
| Action type | NON, FLW (follow type SV), RST/ RUN, HLD and ADV |
| Isolation | Insulated between DI input and various outputs (not insulated from system and various inputs) |
| Program (optional) | |
| Registrable pattern | 1 |
| Number of steps | 9 maximum |
| Program setting range | |
| Level | Same as measuring range |
| Time | 1–9999 minutes/step |
| Ramp | To be set automatically according to level and time |
| Number of executions | 9999 maximum |
| PID output limiter | To be set selectively from 3 types of PID & output limiter |
| External control input | DI/non-voltage 1 point (RUN/RST, HLD, ADV) |
| Action status output | RUN, END and STEP to be selectively output to event output |
| CH2 and CH3 in SV follow setting | Program to be executed by making CH2 or CH3 deviation-follow to pattern set in CH1 in SV follow |
| setting. Not in SV follow setting, program is executed in FIX mode. | |
| Additional functions | Temporary suspension (HLD), carry-forward (ADV), PV start |
| Analog output (optional, selectable between this function and communication) | |
| Number of output | 1 |
| Output types | Selectable from CH1_PV, CH2_PV, CH3_PV, CH1_SV, CH2_SV, CH3_SV, CH1_OUT, CH2_OUT and CH3_OUT |
| Output rating | 0–10mV DC/Output impedance 10Ω |
| 0–10V DC/Load current 1mA maximum | |
| 4–20mA DC/Load resistance 300Ω maximum | |
| Output accuracy | ±0.3%FS (to displayed value) |
| Output resolution | Approx. 1/8000 |
| Output updating cycle | 0.5 seconds |
| Output scaling | Within measuring range (inverted scaling possible |
| Isolation | Insulated between analog output and various inputs and system (not insulated between analog output and control outputs I, P and V) |
| Communication (optional, selectable between this function and analog output) | |
| Communication type | RS-232C, RS-485 |
| Communication system | Half duplex start-stop synchronous system |
| Communication speed | 1200, 2400, 4800, 9600, 19200bps |
| Data format | 7 bits, 8 bits, no parity, even parity selectable |
| Communication address | 1–99 |
| Communication code | ASCII code |
| Communication protocol | Shimaden standard protocol |
| Communication format | Control code selectable, BCC check arithmetic system selectable |
| Isolation | Insulated between communication signal and system/input/output |
| Others | Meets the EMC standards with an additional clamp filter (E04SR301334, SEIWA Information Systems Co.,LTD) |
| Others | |
| Data storage | By non-volatile memory (EEPROM) |
| Ambient temperate/humidity ranges | -10–50 °C/below 90% RH (on condition that there is no dew condensation) |
| Temperature for storage | Between-20 and 65 °C |
| Power voltage | 100V–260V AC ±10% (50/60 Hz) |
| Power consumption | 18VA maximum |
| Input noise removal ratio | Normal mode 45 dB minimum (50/60 Hz) |
| Common mode 140 dB minimum (50/60 Hz) | |
| Applicable standard | RoHS: EN50581 |
| Insulation resistance power terminal | Between input/output terminals |
| 500V DC 20MΩ minimum | |
| Between input/output terminals and protective conductor terminal: 500V DC 20MΩ minimum | |
| Dielectric strength | : 1 minute at 2300V AC between input/output terminals and power terminal (inductive current 5mA) 1 minute at 2300V AC between power terminal and ground terminal (inductive current 5mA) |
| Protective structure | Dust and splash proof front panel equivalent to IP66 (applicable only when panel thickness is 1.2 to 3.2 mm) |
| Material | PPE resin molding (equivalent to UL94V-1) |
| External dimensions | 96 x 96 x 110 mm (Panel depth: 100 mm) |
| Mounting | Push-in panel (one-touch mount) |
| Panel cutout size | H92 x W92 mm |
| Weight | Approx. 420 g |
Ordering Information
| ITEMS | CODE | SPECIFICATIONS | ||||||||||||||
| SERIES | MR13 – | MPU-Based 3 Channel Auto-Tuning PID Controller DIN 96 x 96mm | ||||||||||||||
| INPUT | 1 | Thermocouple B, R, S, K, E, J, T, N, PLII, WRe5-26, U, L | Multi-input Multi-range |
|||||||||||||
| 2 | R.T.D. Pt100 / JPt100 | Multi-range | ||||||||||||||
| 3 | Voltage (mV) -10–10, 0–10, 0–20, 0–50, 10–50, 0–100mV DC | Multi-input Programmable Range |
||||||||||||||
| 4 | Current (mA) 0–20, 4–20mA DC | |||||||||||||||
| 6 | Voltage (V) -1–1, 0–1, 0–2, 0–5, 1–5, 0–10V DC | |||||||||||||||
| CONTROL OUTPUT | Y1- | Contact: Proportional Cycle 0.5–120.0 sec. Contact capacity: 240V AC 2.5A / resistive load |
||||||||||||||
| I1- | Current: 4–20, 0–10mA DC Load resistance: 600Ω max. | |||||||||||||||
| P1- | SSR drive voltage: Proportional Cycle 0.5–120.0 sec. Output rating: 15V±3V DC / 20mA max. |
|||||||||||||||
| V1- | Voltage: 0–10V DC Load current: 2mA max. |
|||||||||||||||
| PROGRAM FUNCTION (OPTION) | N | None | ||||||||||||||
| P | 1 Pattern, 9 step | |||||||||||||||
| EVENT OUTPUT (OPTION) | 0 | None | ||||||||||||||
| 1 | Contact (1a common): 240V AC 1A / resistive load EV1, EV2, EV3 / 3 Point | |||||||||||||||
| REMOTE OR DI INPUT (OPTION) | 00 | None | ||||||||||||||
| 04 | 4–20mA DC Receiving resistance: 250Ω | |||||||||||||||
| 05 | 1– 5V DC Input resistance: 500kΩ min. | |||||||||||||||
| 06 | 0–10V DC Input resistance: 500kΩ min. | |||||||||||||||
| 51 | DI Non-Voltage Contact, Open Collector Input | |||||||||||||||
| ANALOG OUTPUT OR COMMUNICATION FUNCTION (OPTION) |
00 | None | ||||||||||||||
| 03 | Voltage 0–10mV DC, Output resistance: 10Ω | |||||||||||||||
| 04 | Current 4–20mA DC, Load resistance: 300Ω max. | |||||||||||||||
| 06 | Voltage 0–10V DC, Load current: 1mA max. | |||||||||||||||
| 15 | RS-485 | |||||||||||||||
| 17 | RS-232C | |||||||||||||||
| REMARKS | 0 | Without | ||||||||||||||
| 9 | With (Please consult before ordering.) | |||||||||||||||
Reviews
There are no reviews yet.